ENGLISHThis Liquid Crystal Projector can display various computersignals and NTSC/PAL/SECAM video signals. Outline(1) High brightnessA highly efficien
10MUTE buttonSilences the sound. (Cancels the mute whenthe unit is set in mute mode.)VOLUME buttonAdjusts volume. The sound is loud or lowwhile pressi
11ENGLISHSlide the battery compartment coverin the direction of the arrow whilepressing slightly down on it.CautionCautions on use of batteries• Do no
12Please basically use liquid crystal projector at the horizontalposition. If you use liquid crystal projector by the lens up position, the lensdown p
13ENGLISH7Press the INPUT button or the INPUT SELECT (VIDEO orRGB) button to select the source of the signal to be projectedon the screen.• The select
14Basic operations (continued)• To reduce temperature inside the projector, fan will rotate for about 1 minute after the lampis turned off.• Do not tu
15ENGLISHBasic operations (continued)MAGNIFYING FUNCTIONIt is possible to display a partially magnified picture. This function can be used in combinat
16Press the MENU ( ) buttons or the MENU ON /OFF button.• On-screen menus are displayed on the screen.1Select the menu to be adjusted using the MENU (
17ENGLISHRGB signal inputVIDEO signal inputThe menu SET UP serves for the change of parameters influencing the picture and forthe move picture positio
18Adjustments and functions (continued)The menu INPUT serves for the selection of input source.INPUT SETUP INPUT IMAGE OPT.RGB1RGB2VIDEOSETUP INPU
19ENGLISHThe menu OPT. allows you to control communication function etc.Adjustments and functions (continued)SETUP INPUT IMAGE OPT.COM. SPEEDCOM. B
2•VGA and XGA are trademarks of IBM (International Business Machines Corporation).•Macintosh is registered trademark of Apple Computer Corporation of
201. Input / output signalConnection to the RGB signal terminal2. Signal input / output terminal511061511D-sub 15pin shrink terminal(Female)1. Input s
21ENGLISH3. Example of computer signalNote 1: Signal modeNote 2: MAC adapter is necessary to the resolution mode.Projector is compatible with 13 inch
224. Initial set signalsThe following signals are initially set. The settings may be different depending on the computer type. Inthis case, adjust the
23ENGLISH1. Control signal terminalConnection to the control signal terminal2. Mouse emulation511061511D-sub 15pin shrink terminal (Male)CautionTurn o
24Connection to the control signal terminal (continued)PS/2 mouseADB (Mac) mouse214365214365871091211141315CLKDATASEL0RTSGND+5VDATAGND+5VCLK2143652143
25ENGLISHConnection to the control signal terminal (continued)3. Communication(1) Connect the projector and computer using RS 232C cable.(2) Turn off
26Connection to the control signal terminal (continued)Command dataCautionIf computer sends the undefined command code or data code, Projector can not
27ENGLISHThe procedure of getting the Projector status(1)Computer sends the command '20H'+'yyH' to Projector.(2)Projector reply th
28S-VIDEO INRGB INCONTROLAUDIOOUTAUDIO IN12RGB OUT12VIDEO INAUDIO INLRMONOExample of system setupConnecting various equipment.AC InletComputer(Desk ty
29ENGLISHClean the air filter about every 100 hours.Cleaning the air filterTurn the main power switch off and disconnect the powerplug from the power
3ENGLISHBefore useExamples of illustrated marks(Before Use)Illustrated marks Various illustrated marks are used in this product and instruction manual
30LampLight source lamp has a service life.The picture will become dark or color will be poor when the lamp is used for a long time.If usage of lamp i
31ENGLISHReplace the lamp with new one andfix it using the same two screws.• Firmly tighten the lamp screws. Loose screws may causebad connection of t
32On-screen displayThe following messages are displayed on the screen.Message table*1 This message are not displayed after 3 minutes.But this message
33ENGLISHCheck the following again before asking for service. If the trouble cannot be recovered, consult your dealer.When you think something wrong•
34SpecificationsAll dimensions shown in inches.• All specifications are subject to change without notice.Dimension diagram1.110.19.82.213.013.23.94.20
Warning4If any abnormality occurs.• When there is an abnormal smell or smoke, ifyou use this unit as it is, this could cause a fireor electric shock,
• If the cord is damaged (core wire isexposed, disconnected, etc.), askyour dealer to replace it. It maycause a fire, electric shock, etc.• Check that
When you are not going to use for along time.When you are not going use this unitfor a long time because you are goingon a trip, etc., be sure to pull
7ENGLISHCautionDo not place this unit where it gets hot.Be careful since if you place the unitoutdoors, in a place exposed to directsunlight or near a
8Main unitLensSpeakerSpeakerRemote controlsensor• Use the remote control transmitter within the rangeof about 16 feet from the remote control sensor a
9ENGLISHNames and functions of each part (continued)RGB input terminalD-sub 15pin shrink terminal (1/2)VIDEO input terminal(on video-equipped models o
Kommentare zu diesen Handbüchern