POWER TOOLSTECHNICAL DATAANDSERVICE MANUALRECIPROCATING SAWCR 13VASPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENTLIST No. E93
--- 8 ---(2) BI-METAL bladesThe blade numbers of BI-METAL blades in Table 2 are engraved in the vicinity of the mounting position of eachblade. Selec
--- 9 ---6. COMPARISONS WITH SIMILAR PRODUCTS6-1. For USA MarketMaker HITACHIModel CR 13VA 120 11.0 1-1/4 0 -- 2,800 1,0
--- 10 ---Swing cuttingOrbital cuttingOrbital cuttingOrbital cutting function is not provided.Orbital cutting function is not provided.Orbital cutting
--- 11 ---Swing cuttingOrbital cuttingOrbital cutting function is not provided.Orbital cutting01020 30 40 50CR 13VABCDEFCutting time (sec./cut)Straigh
--- 12 ---7-3. Cutting Wood with Saw Blade Installed Upside DownHITACHI genuine blade No. 121for cutting woodA piece of lauan lumber 130 mm (5")
--- 13 ---7-4. Cutting Operation for Long Blade LifeThe service life of a saw blade may vary depending on the operating conditions such as the type of
--- 14 ---8. PRECAUTIONS IN SALES PROMOTIONIn the interest of promoting the safest and most efficient use of the Model CR 13VA Reciprocating Saw by al
--- 15 ---9. REPAIR GUIDE9-1. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLYPlease follow the precautions below for disassembly and reassembly procedures.
--- 16 ---Loosen the Nylock Bolt (W/Flange) M6 x 35 [47] which secures the fan of the armature ass'y (approximatelytwo turns). Remove the four M
--- 17 ---(3) Disassembly of the blade mounting section (Fig. 5)Remove the Retaining Ring (E-Type) for D14 Shaft [2] from Plunger (A) Set [32] with a
1. PRODUCT NAME ... 12. MARKET
--- 18 ---(5) Disassembly of the Second Shaft (A) [64] section (Fig. 7)Remove the Retaining Ring for D17 Shaft [60] from Second Shaft (A) [64]. While
--- 19 ---(8) Disassembly of Handles (A) [74] and (B) [80] section (Fig. 10)Remove the six Tapping Screws (W/Flange) D4 x 25 [43]. Remove the Grip Co
--- 20 ---Fig. 13-a2. ReassemblyReassembly can be accomplished by following the disassembly procedures in reverse. However, specialattention should b
--- 21 ---(3) Reassembly of the blade mounting section (Figs. 15, 16 and 17)Apply Doubrex 251 grease to the inner circumference of Holder Sleeve (B) [
--- 22 ---(4) Press-fitting plunger (A) into the plunger sleeve (Figs. 18 and 19)Tool required: Special repair tool J-317Apply Nippeco SEP-3A grease t
--- 23 ---* Be careful not to damage Washer (F) [3]. (Fig. 21)Washer (F) has an oval shape to fit the inside of the Gear Cover [31]. Therefore, perf
--- 24 ---9-2. Lubrication(1) Nippeco SEP-3A greaseLip portion of the V-Ring [7] Inner circumference of the Swing Roller [53]Sphere portion of the Rec
--- 25 ---For stator ass'y, or for stator ass'yand noise suppressorFor triac ass'y, or for triac ass'yand noise suppressorFor cord
--- 26 ---10. CONFIRMATION AFTER REASSEMBLY10-1. Lead Wire PrecautionsWhen connecting lead wires, be very careful not to remove the insulation coveri
--- 27 ---11. STANDARD REPAIR TIME (UNIT) SCHEDULESMODEL 10 20 30 406050FixedVariableCR 13VAWork FlowHandle (A),(B)SwitchCordCord ArmorSwitch TriggerF
--- 1 ---1. PRODUCT NAMEHitachi 130 mm (5") Reciprocating Saw, Model CR 13VA2. MARKETING OBJECTIVEThere is increasing demand for a high-speed and
--- 28 ---SABER SAWModel CR 13VA1999•12•20(E1)LIST NO. 0786ELECTRIC TOOL PARTS LIST
--- 29 ---PARTSCR 13VA: ALTERNATIVE PARTSITEMNO.CODE NO. DESCRIPTIONNO.USEDREMARKS1 318-484 WASHER (E) 12 318-453 RETAINING RING (E-TYPE) FOR D14 SHAF
--- 30 ---CR 13VAITEMNO.CODE NO. DESCRIPTIONNO.USEDREMARKS52 318-488 SWING RAIL 253 318-492 SWING ROLLER 254 318-491 PIN D6 155 HITACHI LABEL 156 600-
--- 31 ---Printed in Japan(991220 N): ALTERNATIVE PARTS*PARTSOPTIONAL ACCESSORIESCR 13VAITEMNo.CODE NO. DESCRIPTIONNO.USEDREMARKS* 85 500-434Z CORD 1
--- 32 ---SABER SAWModel CR 13VA [For the U.S.A. and Canada only]2000•2•15(E1)LIST NO. 0786ELECTRIC TOOL PARTS LIST
--- 33 ---PARTSCR 13VA: ALTERNATIVE PARTSITEMNO.CODE NO. DESCRIPTIONNO.USEDREMARKS1 318-484 WASHER (E) 12 318-453 RETAINING RING (E-TYPE) FOR D14 SHAF
--- 34 ---CR 13VAITEMNO.CODE NO. DESCRIPTIONNO.USEDREMARKS52 318-488 SWING RAIL 253 318-492 SWING ROLLER 254 318-491 PIN D6 155 HITACHI LABEL 156 600-
--- 35 ---Printed in Japan(000215 N): ALTERNATIVE PARTS*STANDARD ACCESSORIESCR 13VAITEMNo.CODE NO. DESCRIPTIONNO.USEDREMARKS502 312831 CASE 15518"
--- 2 ---4-1. Selling Point Descriptions (1) Fast cutting speedThe Model CR 13VA can cut various construction materials fast and efficiently thanks t
--- 3 --- (3) Saw blade can be mounted in either direction, upward or downwardThe Model CR 13VA is convenient for cutting materials on the floor or n
--- 4 --- (5) Dust- and water-resistant triple-sealing construction <patent pending>The Model CR 13VA has a triple-sealing construction to prot
--- 5 ---4-2. Descriptions of patent pendingNo. OverseasJapanDescriptionsPatentBlade holder ofsaber sawA detachable mechanism that enables one-hand mo
--- 6 ---5. SPECIFICATIONSMax. cutting size Steel pipe outer diameter 130 mm (5") Wood thickness (for Europe) 300 mm (for US
--- 7 ---5-2. Optional AccessoriesThe cutting speed of the Model CR 13VA is substantially higher than that of the current model, however, theconventio
Kommentare zu diesen Handbüchern