Hitachi GX Series 43GX01B Bedienungsanleitung

PROJECTION COLOR TV 43GX01B OPERATING GUIDE TABLE OF CONTENTS IMPORTANT ...

FRONT PANEL CONTROLS FRONT VIEW -  MENU Button This button allows you to enter the MENU, making it possible to set TV features to your preferen

 POWER light You will see a red light when the TV is turned on.  AI (Artificial Intelligence) sensor The artificial Intelligence sensor will make a

INPUT 2 provides Y-CB-CR jacks for connecting equipment with this capability, such as a DVD. NOTES: DO NOT connect standard VIDEO or S-VIDEO to INP

TIPS ON REAR PANEL CONNECTIONS S-Video connections are provided for high performance laserdisc players, VCRs etc., that have this feature. Use these

NOTE: To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust the sound using the remote

3. Press the INPUT button to view the program from the VCR or laserdisc player. The VIDEO mode disappears automatically after approximately eight seco

will be abnormal if the connection is loose. If you have an S-VHS VCR, use the S-INPUT cable in place of the standard video cable. A single VCR can

 The television's internal speakers.  These speakers are connected to a separate audio amplifier. Use the "AUDIO TO HI-FI" output o

To operate your TV, point the remote control at the remote sensor of the TV and press the TV button. The remote will now control your television. To o

(1) POWER Button Press this button to turn the TV set on or off when the remote is in TV mode. If a SPECIAL EVENT REMINDER is set, it will be displ

IMPORTANT SAFEGUARDS IMPORTANT Follow all warnings and instructions marked on this projection television. CAUTION: TO REDUCE THE RISK OF ELECTRIC

(5) LAST CHANNEL (LST-CH) Button Use this button to select between the last two channels viewed. (Good for watching two sporting evens, etc.). (6)

When an S-VIDEO Input is connected to VIDEO: 1. When an COMPONENT VIDEO: Y-CB-CR Input is connected to VIDEO: 2. (9) MENU, CURSOR Buttons A

and PIP sub-picture tuning, press PIP CH button on the remote. Every press of the PIP CH will highlight the main or sub-PIP source. The top channel

NOTE: 1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan. 2. If a channel is tuned during this SURF scanning, sub-p

STROBE FREEZE Press the FRZ button to freeze four frames of the picture you are currently viewing. Press this button again or PIP to return to norm

(1) VCR Button This button allows the remote to control your VCR by setting it to VCR mode. (2) PRECODED VCR Buttons These buttons transmit the c

used for more than one component. NOTES: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has no

CABLE/SATELLITE, VCR, AUDIO AND DVD CODES (CLU-436UI) VCR BRAND ADVENTURA 00 AIKO 66 AIWA 00 AKAI 13,19,21,26,39 AMERICAN HIGH 07 ASHA 51 AU

PORTLAND 03 PROTEC 33 PULSAR 11,20 QUARTER 16 QUARTZ 16 QUASAR 07,35,41,59 RADIO SHACK 00,09,55 RADIX 09 RANDEX 09 RCA 24,28,35,39,44,6

CABLE BRAND ABC 00, 02, 04, 05, 07, 08, 11 Antronix 25, 43 Archer 23, 25, 43 Belcor 42 Cable Star 42 Cabletenna 43 Cableview 43

paragraph 15.119 of the FCC rules. CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other haza

AUDIO BRAND Jerrold 51 Scientific Atlanta 32 ULTRATEC OSD 1. Press MENU on the remote control to display the different features on your HITACHI P

CHANNEL ID Label channels PAY 1, ABC, etc. VIDEO ID. Label video inputs VCR1, DVD1, etc. FAMILY FAVORITES Allows you to set and view fav

NOTE: To see an auto-demonstration of the on-screen displays with HELP text displayed, press and hold the POWER button on the TV set for approximat

Press CURSOR or to highlight the correct answers to all three questions. Press CURSOR to display the graphic guide. Press EXIT to quit menu or CU

RECEPTION BAND Reception channels for each mode are shown at the left. Refer to your cable or TV guide for channel identification standards. If cer

Add or erase additional channels while in CHANNEL MEMORY using CHANNEL or or the number buttons to change the channel. Press EXIT to quit menu or

NOTE: Each touch of CURSOR or will display the next eight channels. CLOCK SET The time must be set before you can use the CALENDAR, 4 EVENT

Use the number buttons to select which point to adjust: (1) - Upper Left, (2) - Upper Middle, (3) - Upper Right, (4) - Center Left, (5) - Center, (

Press CURSOR to select CHANNEL LIST. Press CURSOR to select preset CHANNEL LIST. Press CURSORto scroll through the preset CHANNEL LIST. Press CUR

Press CURSOR to select VIDEO LIST. Press CURSOR to select preset VIDEO LIST. Press CURSOR or to scroll through the preset VIDEO LIST. Press CUR

7 If the television has been dropped or the cabinet has been damaged, unplug this television from the wall outlet and refer servicing to qualified se

To rename the categories, use the CURSOR buttons to highlight the category you would like to rename. Use THUMB STICK or to change a letter and CUR

Use CURSOR , , or to highlight a favorite channel and the TV will automatically tune to that channel. Press EXIT to remove FAMILY FAVORITES OSD

Press EXIT to quit menu or cursor to return to the previous menu. NOTE: 1. If ANT A and ANT B are in the same SIGNAL SOURCE mode (see page 32), whe

1. The OFF Timer will only activate if the TV was turned on or tuned with the ON Timer and no channel selection was made after this time. If you ch

DISPLAY: ON/OFF will turn the display on or off. MODE: C.C. (Closed Caption) is for the program you are viewing. TEXT is for additional in

Use CURSOR or then CURSOR to select ON or OFF. Press EXIT to quit MENU or CURSOR to return to previous menu. NOTE: 1. When TV set is turned

SHARPNESS Use this function to adjust the amount of fine detail in the picture. RESET When RESET is selected, press CURSOR to return video adjustm

Turn on SUPER CONTRAST to improve picture detail in areas of high brightness. COLOR TEMPERATURE Set this to WARM for hotter colors with more red, or s

Press CURSOR or to highlight the function. Press CURSOR to change the function setting. When the function has an " " in the box, it

This function will automatically adjust volume so each channel has the same average volume level. Use this function to choose picture and audio sett

• Never place the set near or over a radiator or heat generator. • Never place the television in a built-in enclosure unless proper ventilation prov

SPECIAL EVENT REMINDER Use this function to set up to six special events into memory. These events can then be viewed in CALENDAR mode. Press CURSOR

Press CURSOR or to change the month. Press EXIT to quit menu or CURSOR to return to previous menu. If the clock is not set, you can not use this

Do not subject the remote control to shocks such as dropping it on the floor, etc. Physical damage to the precision parts may result. Avoid placing

USEFUL INFO Check these items and try these adjustments SYMPTOMS Be sure external connection is correct Be sure power cord is plugged in Be s

VHF-Band...2 ~ 13 UHF-Band...14 ~ 69 CATV Mid Band...

San Diego, CA 92154 In Canada, please contact 1-800-HITACHI (1-800-448-2244) During business hours Monday-Friday EST 9:00AM-7:

IF THIS TELEVISION DOES NOT OPERATE PROPERLY 22 If you are unable to restore normal operation by following the detailed procedure in your operating i

PART NAME PART NO. ILLUSTRATION CLU-436UI REMOTE CONTROL HL00728 43V TELEVISION STAND SP-43G (Not included, order separately) OPTIONAL H530041

Slide out to remove back cover. HOW TO SET UP YOUR NEW HITACHI PROJECTION TV ANTENNA Unless your TV is connected to a cable TV system or to a cen

HOOK-UP CABLES AND CONNECTORS Most video/audio connections between components can be made with shielded video and audio cables that have phono conne